Wavelength-swept Lasers

Many laser diodes can to some extent be wavelength-tuned by modulating their drive current, essentially because that affects the junction temperature. Because the involved active volume is relatively small, the junction temperature can react quickly to changes of the drive current. Therefore, relatively rapid wavelength tuning is possible.

Without additional measures, one usually cannot achieve precisely linear frequency chirps. One may apply a pre-distortion of the temporal form of the input current to improve that. Further, it is possible to improve the precision of the frequency sweeps by applying opto-electronic feedback [13].

In many cases, the basic operation principle of a wavelength-swept laser is the following. One has a laser, with a gain medium having a relatively large gain bandwidth, and there is a fast bandpass filter in its laser resonator. If the transmission wavelength of the filter is tuned, the laser wavelength follows accordingly, unless certain speed limits are reached. For high-speed tuning, it is advantageous to have a short photon lifetime of the resonator, i.e., ideally a short resonator combined with high round-trip power losses. When approaching the limits of tuning speed, the laser does not reach steady-state performance parameters, e.g. concerning its instantaneous bandwidth, which however may not be a problem for the application. On the other hand, slow frequency sweeps are easily obtained.

The explained principle of operation is typically applied to fiber lasers and to diode lasers, the latter usually in the form of external-cavity diode lasers (ECDLs). The gain medium can then be considered as a semiconductor optical amplifier (SOA). The by far highest sweep frequencies are achieved with semiconductor lasers, having short resonators and low photon lifetimes. On the other hand, fiber lasers can produce substantially higher output powers and can access some additional wavelength regions.

Often used wavelength tuning elements are the following:

• A Fabry–Pérot interferometer can be equipped with a piezo transducer, typically reaching scanning frequencies of tens of kilohertz, sometimes even hundreds of kilohertz (with mechanically resonant excitation).
• For lower scanning speeds, one may also use a diffraction grating in the laser resonator which is tilted with a piezo actuator.
• Some devices are based on MEMS technology (microelectromechanical systems) [14]; low-mass systems are intrinsically faster.

Fourier-domain mode locking (FDML) [5] is similar to active mode locking, where however one does not simply modulate the intracavity losses, but instead the transmission wavelength of an intracavity filter. In addition to the similar operation principle described in the previous section, here one precisely synchronizes the modulation of transmission wavelength with the resonator round trips. As a result, the laser operates in a steady state, with the optical powers in the resonator modes staying constant. What changes periodically is only the output wavelength, but lasing at all wavelength simultaneously occurs in that kind of laser. Compared with the previously explained operation principle of a swept laser source, this operation mode is subject to much less laser noise, since lasing at any particular wavelength does not to be re-established in every resonator round-trip. The photon lifetime is no longer a limiting factor.

The output of such a laser can also be considered as a periodic sequence of strongly chirped pulses, similar to the ultrashort pulses from some ordinary mode-locked lasers, but with the pulse duration being so long that subsequent pulses are actually no longer separated (i.e., with low power in between).

Of course, certain constraints are introduced by the principle of Fourier domain mode locking. The modulation frequency needs to be precisely synchronized with the round-trip time of the resonator. It can actually also be an integer multiple of the round-trip frequency, resulting in a correspondingly higher sweep frequency. For very low sweep frequencies, one would need a very long resonator, which may be impractical; however, such lasers are very useful for high sweep frequencies, which are beneficial for applications like optical coherence tomography (see below). In fact, the highest sweep frequencies – sometimes above 1 MHz even in commercial products – are achieved with Fourier domain mode locking.

It is also possible to realize wavelength-swept laser sources which do not require an intracavity bandpass filter. Instead, they can be based on dispersion tuning [7]. Essentially, this means active mode locking of a laser where the resonator contains elements with large chromatic dispersion. For a constant modulation frequency, the laser will emit short (typically picosecond) pulses at a wavelength which the laser chooses such that the round-trip time matches the modulation frequency. By tuning the modulation frequency within some narrow range, one can tune the laser to operate on different wavelengths. The tuning speed is limited by the need of the laser to find a new steady state.

Another possibility is to use a femtosecond laser and send its output pulses through a delay line with strong chromatic dispersion [3]. That leads to much longer, strongly chirped output pulses, which also perform a frequency sweep. In contrast to other swept sources, the output power is not approximately constant, but undergoes a strong modulations with the sweep frequency. While this technical approach may be relatively expensive, it could be applied to very broadband lasers, leading to the highest possible axial image resolution.

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

Please do not enter personal data here; we would otherwise delete it soon. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him e.g. via e-mail.